[Machinery Safety Stories] Certification & Functional Safety 01: From Machinery Directive to Machinery Regulation
기계안전 인증제도 안전규격
Certification & Functional Safety 1/14
From Machinery Directive to Machinery Regulation
EU Machinery Regulation (EU) 2023/1230
Machinery placed on the EU market from 20 January 2027 must follow the new Regulation.
What stays the same, what is new, and what exporters should check now.
When, and by what date
The date that counts is the placing on the market
Regulation (EU) 2023/1230 was published in the Official Journal on 29 June 2023 and entered into force on 19 July 2023. It applies from 20 January 2027, the day Machinery Directive 2006/42/EC is repealed. The text as first published said the 14th; a corrigendum of 4 July 2023 changed it to the 20th.
A directive takes effect only once each Member State writes it into national law. A regulation applies directly and identically in every Member State, so the small national differences in interpretation give way to a single text.
| Date | What applies |
|---|---|
| 2023-07-19 | Regulation enters into force |
| 2024-01-20 | Provisions on notified bodies apply early |
| Placed on the market by 2027-01-19 | Declaration of conformity under Directive 2006/42/EC |
| Placed on the market from 2027-01-20 | Declaration of conformity under Regulation (EU) 2023/1230 |
There is no overlap period. The same model follows the Directive if placed on the market by 19 January and the Regulation if placed on the market on or after 20 January. EC type-examination certificates issued under the Directive remain valid until they expire.
Third-party assessment: Annex I
Part A always needs a notified body; Part B depends
Most machinery is still self-assessed by the manufacturer (module A, internal production control). Higher-risk categories are listed in Annex I of the Regulation, which is split into Part A and Part B.
Annex I Part A · 6 categoriesNotified Body
- Removable mechanical transmission devices and their guards
- Guards for removable mechanical transmission devices
- Vehicle servicing lifts
- Portable cartridge-operated fixing and other impact machinery
- Safety components with self-evolving behaviour using machine learning to ensure safety functions
- Machinery with such embedded systems (for those systems only)
A notified body is required even when all harmonised standards are applied. The options are EU type-examination plus conformity to type (modules B+C), full quality assurance (module H) or unit verification (module G).
Annex I Part B · 19 categoriesConditional
- Circular saws and band saws for wood or meat, hand-fed woodworking machines
- Manually loaded presses for cold metal working, including press brakes
- Manually loaded plastics and rubber injection or compression moulding machines
- Devices for lifting persons with a fall hazard of more than 3 m
- Protective devices that detect persons, logic units ensuring safety functions
- ROPS, FOPS and others
Internal production control (module A) is allowed only when the harmonised standards or common specifications for that category have been applied to all relevant essential requirements. Otherwise Part B also goes through a notified body.
For automation suppliers, the items to watch in Part B are protective devices that detect persons (light curtains, laser scanners) and logic units for safety functions (safety relays, safety controllers). Companies that make and sell these should start with the applicable harmonised standards. The Annex I list can be amended by delegated act.
AI and machines that learn
A topic the Directive never covered
The Regulation is the first to address systems whose behaviour changes through machine learning. When such a system ensures a safety function, it falls under Annex I Part A and needs a notified body. The essential health and safety requirements (Annex III 1.2.1) add several points.
- Scope of action: the machine must not act beyond its defined task and movement space.
- Records: data on the safety-related decision process are recorded and kept for one year.
- Correctability: it must always be possible to correct the machine to keep it inherently safe.
- No changes while learning: neither the machine nor the operator may change settings or rules in a way that could create a hazard, including during the learning phase.
In July 2026 the Digital Omnibus on AI (Regulation (EU) 2026/1744) also amended the Machinery Regulation. The Machinery Regulation moved from Section A to Section B of Annex I of the AI Act, so machinery with AI safety components is assessed under the Machinery Regulation alone. The high-risk AI requirements of the AI Act are to be written into the Machinery Regulation by delegated act by 2 August 2028.
Protection against corruption and malicious attempts
Cybersecurity has become a safety requirement
As more machines are networked, outside interference that defeats a safety function is treated as a hazard. The Regulation adds this to Annex III as section 1.1.9, protection against corruption.
1.1.9 Protection against corruptionAnnex III
- Connecting another device, directly or remotely, must not lead to a hazardous situation.
- Hardware that carries signals or data giving access to critical software is protected against accidental or intentional corruption, and evidence of legitimate or illegitimate intervention is collected.
- Installed software needed for safety is identified and that information is available at all times.
- Evidence of software intervention, modification or configuration change is collected.
1.2.1 Safety and reliability of control systemsAnnex III
- Control systems withstand reasonably foreseeable malicious attempts by third parties.
- Hardware or logic faults, control logic errors and foreseeable human errors do not lead to hazardous situations.
- A tracing log of intervention data and of safety software versions uploaded after placing on the market is kept for five years after upload, for use when an authority asks for proof of conformity.
The European standard written for these requirements, prEN 50742 (Safety of machinery - Protection against corruption), went through public comment on its draft in early 2026. Its relation to IEC 62443, the industrial automation security series, is the topic of part 5.
Instructions may be digital
With conditions attached
The Directive assumed paper instructions. The Regulation allows instructions for use in digital form (Article 10(7)).
- 1
Show how to find them
State how to access the digital instructions on the machine, its packaging or an accompanying document.
- 2
Printable and savable
Users must be able to download, save and print them, and reach them even when the machine has broken down.
- 3
Kept online
They stay online for the expected lifetime of the machine and at least 10 years after placing on the market.
- 4
Paper on request
If requested at the time of purchase, the manufacturer provides paper instructions free of charge within one month.
Technical documentation and the EU declaration of conformity are kept for at least 10 years after placing on the market.
A substantial modification makes you the manufacturer
The rule for rebuilds and retrofits is now written down
The Regulation defines substantial modification (Article 3(16)): a change by physical or digital means, not foreseen or planned by the manufacturer, that creates a new hazard or increases an existing risk and therefore requires either of the following.
- (a) adding guards or protective devices that require changes to the existing safety control system
- (b) additional measures to ensure stability or mechanical strength
Whoever makes a substantial modification takes on the manufacturer's obligations (Article 18), repeats the conformity assessment and declares conformity on their sole responsibility. If only one machine in an assembly is affected, the obligations apply to that machine, as shown by the risk assessment. A non-professional user modifying machinery for personal use is not treated as a manufacturer.
What happens to harmonised standards
Presumption of conformity needs a new listing under the Regulation
Applying a harmonised standard gives a presumption of conformity with the essential requirements. That effect arises only when the standard's reference is published in the Official Journal under the Regulation (Article 20(1)). The 800-odd standards listed under the Directive do not carry over automatically.
| Standard | Status to know now |
|---|---|
| Directive list of harmonised standards | Implementing Decision (EU) 2026/2015 of September 2026 added or revised more than 80 standards; the earlier Decision (EU) 2023/1586 is repealed on 2027-01-20. |
| EN ISO 10218-1/-2:2025 | The 2025 industrial robot standards are in that Directive list. |
| EN ISO 13849-1 | The 2023 edition was listed in May 2024; the 2015 edition is withdrawn after a transition period ending 2027-05-15. |
| prEN 50742 | Written for the corruption requirement (1.1.9); still a draft. |
As of the September 2026 decision, no list of harmonised standards under the Regulation had been published. Check the latest Official Journal list just before shipment, and for new requirements that no standard covers yet (AI, corruption), record the reasoning in the risk assessment and technical file.
Checklist for EU exporters
To finish before 20 January 2027
- 1
Confirm the placing-on-market date
For long projects, the actual placing on the market, not the contract date, decides Directive or Regulation.
- 2
Check Annex I
Decide whether the machine or safety component is in Part A or Part B, and if so, which module to use.
- 3
Add the new essential requirements
Bring 1.1.9 corruption, 1.2.1 malicious attempts and tracing logs, and the self-learning requirements into the risk assessment and design.
- 4
Review the standards list
Check the editions you apply (13849-1:2023, 10218:2025 and so on) and whether they are listed in the Official Journal.
- 5
Update instructions and declaration
Set up digital instructions and change the legal basis of the declaration of conformity to (EU) 2023/1230.
- 6
Tell customers
State in the instructions and contracts that on-site modifications or software changes can be a substantial modification.
Next · 02 Every PLr starts with risk assessment
Following ISO 12100 through hazard identification, risk estimation, risk evaluation and risk reduction, to show where safety functions and PLr come from.